A reversible air conditioner, a heat pump or a split unit works perfectly well, but stays completely mute to the rest of the home or building: no app, no remote access, no link with the rest of the installation. Many manufacturers (Toshiba, Daikin, Mitsubishi Electric, Hitachi, Panasonic, Fujitsu…) offer either no connected module at all, or a closed proprietary module tied to the manufacturer’s own cloud, incompatible with Home Assistant or any third-party building management system. GET Conseil connects equipment that was never designed to be connected, whatever the brand or communication protocol involved.
The problem: an air conditioner or heat pump that talks to nothing
Whether it’s a reversible air conditioner, an air-to-air or air-to-water heat pump, or a simple split unit, the same pattern shows up on a huge number of installations: the equipment was never designed to communicate with anything beyond its own remote or its own thermostat. No access from a smartphone, no data a third-party system can use, and no way to fold it into a scenario that coordinates heating, air conditioning, lighting and shutters together.
The real blocker is almost never the equipment itself, but the communication protocol the manufacturer chose — and there are mainly two types, each requiring a different approach.
Infrared-controlled equipment: an IR gateway is enough
For most residential split units and many consumer heat pumps, control runs through a standard infrared remote. In that case, a network-connected IR gateway is enough: it learns the codes from the existing remote, then reproduces them on demand (on/off, temperature, mode, fan speed) — but this time triggerable from Home Assistant, a scenario, or a presence-based rule.
Wired controllers on a proprietary bus: the most locked-down case
Some equipment, particularly from manufacturers like Toshiba, doesn’t use infrared at all: it’s controlled by a wired wall controller, linked to the indoor unit by a communication bus proprietary to that manufacturer. There’s no infrared signal to capture here — the only way to talk to the equipment is to speak the bus protocol directly. This is exactly the kind of situation where a client ends up stuck: no official connected module available, and no standard home automation installer able to step in.
Real case: unlocking a wired-controller Toshiba air conditioner
GET Conseil handled exactly this case for a client with a Toshiba air conditioner controlled by a wired wall unit on a proprietary bus. No off-the-shelf solution could connect it: no compatible official Wi-Fi module, no infrared signal to learn. Our solution was to install an ESP module (ESPHome) wired directly into the Toshiba communication bus, able to decode and reproduce the frames exchanged between the wall controller and the indoor unit.
The result: equipment the manufacturer never designed to be connected became fully controllable and monitorable from Home Assistant, exactly like any other device on the client’s building management system — temperature, mode, on/off, integrated into the same scenarios and the same dashboard as the rest of the installation.
This kind of custom adaptation is what sets our approach apart from a standard home automation installer limited to a list of “compatible” devices: if your air conditioner, heat pump or split feels like a dead end because it wasn’t designed to be connected, it usually isn’t one.
What about heating?
The same principle applies to existing heating: a relay module for electric radiators, a connected thermostatic valve, or a module on the existing pilot wire for central heating, without replacing the boiler.
The real gain: one building management system, across every brand
The point of going through Home Assistant rather than each manufacturer’s own app is to bring air conditioning, heat pumps, heating, lighting and shutters together into a single dashboard, regardless of each device’s original brand or protocol — and to build scenarios that coordinate them: cutting the air conditioning when a window is left open, adjusting heating based on detected presence, or simply monitoring every zone at a glance.
That’s exactly what makes a building management system more than a pile of isolated connected gadgets — a field where GET Conseil operates as a certified KNX Partner and approved Jeedom installer, also experienced with Home Assistant and with integrating equipment that was never designed to be connected.
Who it’s for: homeowners, SMEs and commercial buildings, any brand
This approach applies just as well to a residential air conditioner or heat pump as to several units at an SME or a school, whatever the brand (Toshiba, Daikin, Mitsubishi Electric, Hitachi, Panasonic, Fujitsu, Carrier, LG…). For larger commercial equipment (multisplit, VRV/VRF), a dedicated Modbus or BACnet gateway may be needed depending on the manufacturer — something we assess during the audit of your installation.
Do you have an air conditioner, heat pump or split that feels stuck because it isn’t connected to begin with? Discover our home & building automation offer, or get in touch to assess your installation, whatever the brand.
Frequently asked questions
My air conditioner or heat pump has no official connected module, is that a dead end?
No. Depending on the original control method (infrared remote or wired controller on a proprietary bus), we use either an IR gateway or an ESP module that decodes the manufacturer’s protocol directly, as we did on a wired-controller Toshiba air conditioner.
Does this work regardless of the brand?
Yes, the principle adapts to most brands (Toshiba, Daikin, Mitsubishi Electric, Hitachi, Panasonic, Fujitsu, Carrier, LG…), whether the original control is infrared or wired on a proprietary bus.
What exactly is an ESP module?
It’s a small microcontroller (flashed with ESPHome) wired directly into the equipment’s communication bus. It decodes the frames exchanged with the original controller and makes them available in Home Assistant, without replacing or modifying the equipment itself.
Why Home Assistant rather than the manufacturer’s app?
Because one app per manufacturer means scattered, device-by-device control. Home Assistant brings air conditioning, heat pumps, heating, lighting and shutters together into a single dashboard, regardless of each device’s original brand.
